44
9152BINDCO02/10
ATA8743
Notes: 1. These options should only be used when not operating close to the maximum frequency of the
device, and only if frequency stability at start-up is not important for the application. These
options are not suitable for crystals.
2. These options are intended for use with ceramic resonators and will ensure frequency stability
at start-up. They can also be used with crystals when not operating close to the maximum fre-
quency of the device, and if frequency stability at start-up is not important for the application.
14.5 Low-frequency Crystal Oscillator
To use a 32.768 kHz watch crystal as the clock source for the device, the low-frequency crystal
oscillator must be selected by setting CKSEL fuses to 0110. The crystal should be connected
as shown in Figure 14-2. See the 32 kHz Crystal Oscillator Application Note for details on oscil-
lator operation and how to choose appropriate values for C1 and C2.
When this oscillator is selected, start-up times are determined by the SUT fuses as shown in
Table 14-5.
Notes: 1. These options should only be used if frequency stability at start-up is not important for the
application.
Table 14-4. Start-up Times for the Crystal Oscillator Clock Selection
CKSEL0
SUT1..0
Start-up Time from
Power-down and
Power-save
Additional Delay
from Reset
(V
CC
= 5.0V)
Recommended Usage
0
00
258 CK
(1)
14CK + 4.1 ms
Ceramic resonator, fast
rising power
0
01
258 CK
(1)
14CK + 65 ms
Ceramic resonator, slowly
rising power
0
10
1K CK
(2)
14CK
Ceramic resonator, BOD
enabled
0
11
1K CK
(2)
14CK + 4.1 ms
Ceramic resonator, fast
rising power
1
00
1K CK
(2)
14CK + 65 ms
Ceramic resonator, slowly
rising power
1
01
16K CK
14CK
Crystal Oscillator, BOD
enabled
1
10
16K CK
14CK + 4.1 ms
Crystal Oscillator, fast
rising power
1
11
16K CK
14CK + 65 ms
Crystal Oscillator, slowly
rising power
Table 14-5. Start-up Times for the Low Frequency Crystal Oscillator Clock Selection
SUT1..0
Start-up Time from
Power Down and Power
Save
Additional Delay from
Reset (V
CC
= 5.0V)
Recommended usage
00
1K CK
(1)
4 ms
Fast rising power or BOD
enabled
01
1K CK
(1)
64 ms
Slowly rising power
10
32K CK
64 ms
Stable frequency at start-up
11
Reserved
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ATAVRRZ200
KIT DEMO AT86RF230
AV101-12LF
ATTENUATOR HIP3 0.70-1GHZ 8-SOIC
AV102-12LF
ATTENUATOR HIP3 1.7-2GHZ 8SOIC
AV113-12LF
ATTENUATOR HIP3 2.1-2.3GHZ 8SOIC
AXUV100G
SENSOR ELECTRON DETECTION
B0205F50200AHF
XFRMR BALUN RF 200-500MHZ 1608
B0310J50100AHF
XFRMR BALUN RF 300-1000MHZ 0805
B0322J5050AHF
XFRMR BALUN RF 300-2200MHZ 0805
相关代理商/技术参数
ATAB5275
功能描述:射频开发工具 LF Tx Antenna driver board (TPMS) RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
ATAB5276
功能描述:射频开发工具 1A Antenna Driver Demoboard RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
ATAB5278
功能描述:射频开发工具 LF Tx Antenna driver board (PEG) RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
ATAB5279
功能描述:射频开发工具 LF Transmitter with ATA5279 RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
ATAB5282
功能描述:BOARD EVAL LF 125KHZ ANT DVR 3CH RoHS:是 类别:RF/IF 和 RFID >> RFID 评估和开发套件及电路板 系列:Smart RF 产品培训模块:M24LR64 Dual Interface EEPROM 标准包装:1 系列:- 类型:读取器模块 频率:13.56MHz 适用于相关产品:M24LR-64-R 已供物品:2 根基准天线，I2C 和 RFID 读取器，样品 其它名称:497-10480
ATAB5283
功能描述:射频开发工具 LF Rx Board 1 channel (TPMS)
RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
ATAB5423-3-B
功能描述:射频开发工具 UHF Transceiver Base station Board 315MHz
RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
ATAB5423-3-WB
功能描述:射频开发工具 UHF TRx Application Board 315MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V